Proxim ORiNOCO AP-2500 Manual do Utilizador Página 80
- Página / 250
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
80
Network Parameters
• The WDS link shares the communication bandwidth with the clients. Therefore, while the maximum data rate for
the Access Point’s cell is still 11 Mbits/sec, client throughput will decrease when the WDS link is active. The
connection over the link will be slower than if the client were communicating directly with the AP-2500.
• If there is no partner MAC address configured in the WDS table, the WDS port remains disabled.
• Each WDS port on an AP should have a unique partner MAC address. Do not enter the same MAC address twice
in an AP’s WDS port list.
• Each Access Point that is a member of the WDS must have the same Channel setting to communicate with each
other.
• Auto Channel Selection must be disabled to create a WDS link.
• Each Access Point that is a member of the WDS must have the same WEP Encryption settings. Therefore, if you
want to encrypt the WDS link, you must configure each Access Point to use WEP encryption and each
Access Point must have the same Encryption Key (Key 1). See Encryption.
• If your network does not support the Spanning Tree protocol, be careful to avoid creating network loops between
APs. For example, creating a WDS link between two Access Points connected to the same Ethernet network will
create a network loop. The AP-2500 does not support Spanning Tree.
WDS Setup Procedure
To setup a WDS link between an AP-2500 and an AP-2000 or AP-600b, follow the steps below for each AP that you
wish to include in the Wireless Distribution System.
1. Confirm that the AP-2500 is connected to the Ethernet network in your proposed WDS topology.
2. Write down the MAC addresses of the APs that will be part of the WDS link.
3. Login to the AP-2500’s Web browser interface.
4. Click Configure > Interfaces > Wireless (A or B) to open the configuration screen for the radio that will use WDS.
5. Disable Auto Channel Select if necessary.
6. Write down the Frequency Channel in use.
7. Scroll down to the Wireless Distribution System heading.
8. Click the Edit button to update the Wireless Distribution System (WDS) Table.
9. Enter the MAC address for the AP-2000 or AP-600b in one of the Partner MAC Address field of the WDS Table
Configuration screen.
10. Set the Status of the device to Enable.
11. Click OK
.
Figure 4-12 WDS Configuration
12. Restart the AP.
13. Login to the AP-2000 or AP-600b’s Web browser interface.
- ORiNOCO AP-2500 1
- Copyright 2
- Trademarks 2
- Document Conventions 2
- Contents 10
- Introduction 13
- Networking Features 16
- The Product Package 20
- Minimum System Requirements 20
- Web Browser Interface 21
- Command Line Interface 21
- SNMP Management 21
- Prerequisites 23
- Hardware Installation 24
- AP-2500 with Power Supply 26
- Installing a Card in Slot B 28
- 5 GHz Kit Installation 28
- Initialization (ScanTool) 31
- Basic Configuration 33
- Set and Change Passwords 38
- Configure the Date and Time 39
- Download the Latest Software 40
- Uploading Configuration Files 41
- Authentication Overview 43
- Internal Authentication 44
- End User Experience 45
- Authentication Procedure 51
- Notes Concerning RADIUS 52
- Configure the AP-2500 55
- External Authentication 58
- Configuration Instructions 59
- IP Configuration 63
- DHCP Server 63
- DNS Server 68
- Typical VLAN Configurations 69
- Wireless (802.11a) 74
- Wireless (802.11b) 75
- Management 81
- IP Access Table 82
- Services 82
- Filtering 84
- Static MAC 85
- Alarm Host Table 87
- Security 88
- Encryption 99
- Network Parameters 100
- Public Space Parameters 101
- Home Page Redirection (HPR) 102
- AAA Basic 103
- General Syslog Information 125
- Configuration Instructions 126
- Sample Logging Events 127
- URL Filtering 131
- URL Filtering by IP Address 132
- ICC Appearance 133
- Customizing the ICC 134
- SMTP Redirection 137
- Passthrough Addresses 138
- Passthrough DNS Table 139
- Bandwidth Management 140
- Creating a Free Billing Plan 145
- Subscriber Messages 146
- Enabling Cookie Support 150
- Authorized Subscribers 153
- Manually Adding a Subscriber 154
- Removing a Subscriber 155
- Monitor Information 156
- System Status 157
- IP/ARP Table 160
- Learn Table 161
- Current Subscribers Table 162
- DAT Sessions 163
- Interfaces 164
- Link Test (802.11b Only) 165
- Commands 167
- File Type Overview 168
- Download Instructions 168
- Help Link 171
- Troubleshooting 172
- Troubleshooting Concepts 173
- Symptoms and Solutions 173
- Client Connection Problems 175
- VLAN Operation Issues 176
- Active Ethernet 176
- Recovery Procedures 177
- System Alarms (Traps) 181
- Related Applications 182
- LED Indicators 183
- In This Chapter 184
- Notation Conventions 185
- Important Terminology 185
- Navigation and Special Keys 185
- CLI Error Messages 186
- Bootloader CLI 186
- CLI Command Types 187
- ? (List Commands) 188
- Parameter Control Commands 193
- Working with Tables 195
- Using Strings 196
- “set” CLI Command 197
- “show” CLI Command 197
- Other Network Settings 201
- Re-enable ACS 202
- Set the Multicast Rate 203
- Set Communication Ports 203
- Set Session Timeouts 203
- Configure Management Ports 204
- Edit IP Access Table 204
- Parameter Tables 205
- System Parameters 206
- DHCP Server Parameters 208
- DNS Parameters 208
- Interface Parameters 209
- Wireless 802.11a Parameters 211
- Management Parameters 212
- SNMP Parameters 213
- Telnet Parameters 213
- Serial Port Parameters 214
- HTTP (web browser) Parameters 214
- TFTP Server Parameters 214
- NTP Parameters 215
- Security Parameters 216
- Encryption Parameters 218
- AAA Parameters 219
- Logging Parameters 220
- URL Filtering Parameters 221
- ICC Button Configuration 222
- SMTP Parameters 223
- Passthrough Parameters 223
- Passthrough IP Table 224
- AAA Passthrough Port 224
- Billing Parameters 225
- Billing Plans Configuration 226
- Authorized Subscribers Table 229
- Miscellaneous Parameters 231
- CLI Monitoring Parameters 231
- XML Interface Specification 232
- XML POST 233
- XML Response Form Format 234
- AP Command Reference 235
- Bandwidth Up 236
- Bandwidth Down 236
- Delete User 236
- Query User 237
- Authorize User 237
- Commands For Reference Only 238
- ORiNOCO AP-2500 User Guide 242
- Explanation: 243
- ASCII Character Chart 244
- Specifications 245
- Radio Specifications 247
- Wireless Communication Range 248
- Technical Support 249
Manuais e produtos relacionados com Pontos de acesso WLAN Proxim ORiNOCO AP-2500
(72 páginas)Lucent Technologies 20A-USB podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Sprzęt komputerowy Lucent Technologies 20A-USB.
Dostarczamy 1 pdf podręczników Lucent Technologies 20A-USB do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentários a estes Manuais